Nissan Versa Forums banner
1 - 10 of 10 Posts

·
Registered
Joined
·
41 Posts
Discussion Starter · #1 ·
I just received my pair of new mirrors today. I waited 3 weeks for them to come from Malaysia. It's designed for the Tiida/Latio model. It's a blue anti glare wide angle LED signal mirror made by a company called HSR. The mirrors are also suppose to be water repellent.

When I received them, I noticed the OEM mirror is bigger than the tiida mirror, but the back piece fits into the mirror housing. You can see from the pictures. It does leave a bigger gap, which I will try to use rubber molding and a mirror vent visor to fill that in.

I enjoyed driving with them. The driver side mirror is wide angled, and eliminates the blind spot, but the cars look a lot closer than they are. I guess I'll get used to it. They look really cool, and at night it really cuts down the glare which is what I wanted.

I didn't connect the LED wire, because I thought the signal would be distracting. But I did tap it to a battery to show you guys what it would look like. I just wanted the anti glare feature. The mirrors ran me about $103. Email [email protected] if interested.

Nissan Latio Blue Side Mirror w LED Signal (Kuala Lumpur, end time 7/3/2012 2:15:00 PM MYT)
 

Attachments

·
Registered
Joined
·
41 Posts
Discussion Starter · #2 ·
More pictures
 

Attachments

·
Registered
Joined
·
41 Posts
Discussion Starter · #4 ·
Thanks, it ran me about $103. I did a lot of research on it, and I could only find them in asia. I saw one on ebay, but it didn't come with the back piece, and it wasn't wide angled.
 

·
Registered
Joined
·
147 Posts
Looking good
 

·
Registered
Joined
·
41 Posts
Discussion Starter · #8 ·
Thanks guys, the black piece is the back plate for the mirror, it comes attached to the mirror glass already, unlike the seller on ebay which you have to attach it to your own glass, by heating it up, etc. The wire is for the turn signal. I didn't want that feature, so I left the wire hanging inside the mirror housing.
 

·
Registered
Joined
·
132 Posts
I just received my pair of new mirrors today. I waited 3 weeks for them to come from Malaysia. It's designed for the Tiida/Latio model. It's a blue anti glare wide angle LED signal mirror made by a company called HSR. The mirrors are also suppose to be water repellent.

When I received them, I noticed the OEM mirror is bigger than the tiida mirror, but the back piece fits into the mirror housing. You can see from the pictures. It does leave a bigger gap, which I will try to use rubber molding and a mirror vent visor to fill that in.

I enjoyed driving with them. The driver side mirror is wide angled, and eliminates the blind spot, but the cars look a lot closer than they are. I guess I'll get used to it. They look really cool, and at night it really cuts down the glare which is what I wanted.

I didn't connect the LED wire, because I thought the signal would be distracting. But I did tap it to a battery to show you guys what it would look like. I just wanted the anti glare feature. The mirrors ran me about $103. Email [email protected] if interested.

Nissan Latio Blue Side Mirror w LED Signal (Kuala Lumpur, end time 7/3/2012 2:15:00 PM MYT)
I had it on my previous mods but the bad side is that The mirror is very hard to remove and insert in the frame. It took me three hours to finish all the set up however the best way to accomplish this is by using a heat gun which is set up on the low settings. On the other hand, Im recommeding check out first the service bulletin before doing your job.
 

·
Registered
Joined
·
321 Posts
I would love a set. But I really hate the gap it leaves. Not trying to knock yours they look good, and the features are nice as well but its not for me :shrug:
 
1 - 10 of 10 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top