Nissan Versa Forums banner
1 - 20 of 27 Posts

·
Registered
Joined
·
452 Posts
Discussion Starter · #1 ·
Absolutely. We should have them in stock next week. How much tq do you expect to make with the blower ?



David Norton
P 800-828-4379 Ext: 110
F 205.491.8593

http://www.specclutch.com



--------------------------------------------------------------------------------

From: Spec Clutch Web Site [mailto:[email protected]]
Sent: Saturday, August 28, 2010 2:27 PM
To: [email protected]
Subject: Spec Contact Form



Spec Clutch

Comment — Nissan versa


hey i was wondering if their was any possibilty of yall making a stage 2 or stage 3 clutch for the versa, as there is a supercharger coming out for the versa in a few months i was wondering if there would be any possibility of yall making a clutch being as i would like to up the boost pressure a tad bit thanks for your help bye.



This email has been generated by specclutch.com. Please do not respond
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #2 ·
Havent really told him much more as I will probably go turbo if they make the clutch but this has been a pretty positive week for parts, I havent got too many turn downs lately if they make this tho this will be a definate next mod for me i dont know about yall but this is putting me closer to my goal :p hope yall are having a good week and hope to hear some positives on this.
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #4 ·
mine is gona cost me 450 for a stage 3 that will be able to hold 220ft lbs of torque they said the drivability shouldnt really be affected im trying to talk to them about a flywheel also so we shall see how that goes but tango dont go and throw the stage 3 in your car without the power to back it up :p
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #6 ·
Its honestly kind of a one off thing right now its being built to whatever specs i want more or less, thats why its going to be able to handle 285 hp and 220 ft lbs of torque.. figure with the supercharger on the way might as well get something that can handle a little extra the one im going to end up getting is a stage 3 if you go on their site they more or less explain the setups of their clutches from what the representive told me they needed to crunch some numbers and see but he thought the stage 3 would be very driveable if you would like i can post all the emails i have had back and fourth between me and spec if you would like that information or you could just contact them theyre actully pretty awesome about answering usually i get an email back in 30 minutes or so.
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #8 ·
can only get ahold of that guy 3 days a week lol
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #10 ·
Yes, but we have not made on for the Versa yet..it would be a VERY good
thing for that car...super big gains. If I can get a sample for a day or
two, I can make it worthwhile for whoever provides it..

David Norton
P 800-828-4379 Ext: 110
F 205.491.8593
http://www.specclutch.com


-----Original Message-----
From:
Sent: Thursday, September 02, 2010 3:47 PM
To: David Norton
Subject: RE: Spec Contact Form

yall also make flywheels correct?
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #11 ·
Major Update!!!

Sorry for the delayed reply..I have been out of town. I have the clutch in
stock. All stages are available except st3, 4 and 5. The st2+ will hold
210 ft lbs torque and the st3+ 260 ft lbs..obviously the hp numbers would be
a lot higher, but clutches hold tq, not hp. Both of those stages will
drive like a dream. We can make them stronger, but at the expense of pedal
effort, and we're not sure how much pedal feedback the Versa's firewall and
hydraulics can take. But we now our high clamp pressure plate works well,
and it is several hundred psi over stock in clamp load.
We still need a flywheel sample. It would be good to have a flywheel not
installed in a car, as we will need 4-5 weeks to get the material in and run
the flywheel. I won't need the flywheel but a couple days, so I can return
it quickly. So if someone bought a clutch, we would install it free in
return for letting us get dimensions off the flywheel.

David Norton
P 800-828-4379 Ext: 110
F 205.491.8593
http://www.specclutch.com


-----Original Message-----
Sent: Tuesday, September 14, 2010 10:22 AM
To: David Norton
Subject: RE: Spec Contact Form

if no one else contacts you ive posted about it on our forum if need be ill
drive to alabama, depending on what the deal is with the flywheel and clutch
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #13 ·
will do how did you manage to get a 3d model of the flywheel in the first place?
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #15 ·
If it has all the measurements it may work. But we need measurements to the
.001 inch. thats the last thing he told me so if you can get it that close by all means let me know man
 

·
Registered
Joined
·
452 Posts
Discussion Starter · #16 ·
hey promised land you might wana contact this guy directly usually you can get him ahold of him from 11 am et to 4pm since i dont have the specs it would be probably much easier for you to communicate with him on this.
 

·
Registered
Joined
·
1,285 Posts
1 - 20 of 27 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top